OEM Literature for Manufacturers

Hub Types

SPEEDHUB Variations

Even though the range of bicycles available nowadays is incredibly varied, the Rohloff AG has a SPEEDHUB to fit almost every frame.

The construction of the SPEEDHUB is based around a modular system. The classic SPEEDHUB versions are constructed for a 135mm O.L.D. and available with a choice of quick-release (CC) or threaded axle (TS). In the past years, the Rohloff AG have extended the SPEEDHUB range to remain compatible with modern, alternative mounting options. As such, we are pleased to confirm that SPEEDHUBs are currently available to fit numerous frame spacings from 135mm to 197mm for fatbikes with 12mm thru axle system.

  Classic   Boost XL   XXL  
O.L.D. (mm) 135 142 148 170 177 190 197
TS (threaded axle M10x1) ✔️     ✔️      
CC (hollow axle) ✔️     ✔️   ✔️  
A-12 (for 12mm Thru-axle frames)   ✔️ ✔️   ✔️   ✔️
36 hole rim ✔️ ✔️ ✔️        
Tandem ✔️ ✔️ ✔️ ✔️ ✔️ ✔️ ✔️

Available Colors

Black? Red? Silver? All SPEEDHUB versions with the exception of XL and XXL units, are available in these 3 colors (XL and XXL units only available in black).

black: anodized

red: anodized

silver: anodized

 

Braking system

Regardless whether you wish to decelerate with rim or disk brakes, the SPEEDHUB can be used with either system. Rim brake specific versions are supplied with a smooth, polished hub cap, whereas disc brake versions are supplied with a hub-cap incorporating a 4-hole brake rotor mount.

 

Rim brake specific hub-cap

 

Disc brake compatible hub-cap

Axle type

One of three main axle types are used on bicycles nowadays. The classic 10mm threaded axle, the 10mm quick release axle and the 12mm thru-axle. SPEEDHUBs are available with an axle system to suit each of these bicycle dropout styles.

Cross Country (CC)

Hollow axle for use with a standard Q/R skewer

Touring Spindle (TS)

Standard solid, threaded axle (M10x1).

 

Torque anchoring apparatus

Frame construction is an art-form. As with every art form, the artist/fabricator wishes to leave their signature and this is often achieved through the dropout design. The Rohloff AG are pleased to offer 4 different methods of anchoring SPEEDHUB output torque to the bicycle frame, so that we remain compatible with nearly all dropouts styles available to a frame fabricator.

OEM: Axleplate
OEM2: Axleplate
Standard
PM: Post Mount

Gear Mechanism

Further options; our ultimate goal is to retrofit as many bicycles as possible with a SPEEDHUB transmission. Two different gear mechanisms are thus available to help us achieve this goal. An internal gear mech (which sits inside the dropouts, directly on the gear-unit) and an external gear mech (where a cable box is located outside of the dropout away from brake rotors). The internal gear mech not compatible with disc brake versions.

Electric Gear Mech (E-14)
External Gear Mech.
Internal Gear Mech.

 

Shell versions

Two different shells (Regular & XL) are available to cover the numerous O.L.D.'s in which a SPEEDHUB is available. This ensures Fatbike riders are not excluded from enjoying the advantages of SPEEDHUB use.

Regular

O.L.D.: 135/142/148 mm

XL

O.L.D.: 170/177/190/197 mm

Version 1: OEM Specific Left-hand Dropout

This version is particularly suitable for rear suspension frames. In order to compensate for the altering chain length as the rear triangle moves, an external chain tensioner will also be required. Both CC (hollow, quick-release) and TS (M10x1 threaded) axle versions can be used with this style dropout.

Pointer

It is important to ensure the measurement ’32 -0.5mm’ is not exceeded to ensure there won’t be any clearance issues when mounting an EX cable box (see right-hand illustration of fig 15).

Left-hand dropout mounted with SPEEDHUB 500/14

Chain Tensioner or eccentric BB required.

All necessary measurements can be found on the accompanying technical drawing OA11.

Rohloff SPEEDHUB 500/14 with CC OEM axleplate

CC OEM axleplate (also available as a TS OEM axleplate)

Version 2: Adjustable OEM dropout

This version consists of two basic elements: - the dropout (brazed/weldet to the main bicycle frame) and the dropout insert which is bolted to it. This version is typically used on hardtrail bicycle frames where the chain/belt length does not alter.

The chain tension is altered by moving the dropout insert back and forth, within the actual brazed dropout section. To tension the chain, one simply loosens the securing bolts and pulls the wheel backward until the desired tension is achieved. The bolts are then tightened again to prevent the wheel moving forward under load. The only thing one really needs to check, is that the wheel remains central between the chainstays.

The dropouts may also be machined/drilled and tapped, for mounting a luggage rack and fender.

Fully assembled OEM disc brake dropout

All 3 elements (dropout, dropout insert, mounting bolts) of the adjustable OEM dropout, can be identified in this rendering.

Steel or aluminum cluster (seat), right-hand side

The exact dimensions are shown on the technical drawing OA04.

Steel or aluminum cluster (seat), left-hand side

Left-hand dropout, technical drawing OA13

This and the next image show the left-hand & right-hand dropout inserts designed solely for SPEEDHUB 500/14 use.

Right-hand dropout, technical drawing OA14

Right-hand dropout with derailleur hanger, technical drawing OA28

This dropout also allows the mounting of a rear derailleur. It can therefore be used with the Rohloff SPEEDHUB 500/14 or a conventional derailleur system.

The dropout as in shown Fig. 8 must be fitted to all full suspension bikes where the chain length changes.

OEM dropout insert (DB), disc brake mount on left-hand side, technical drawing OA25

With regards to the installation of a disc brake, this dropout will be necessary.

[hidden]

CNC-Formteile

Lauble & Fichter Rohloff Ausfallenden sind hochwertige CNC gefräste Teile, die der Qualität der Speedhub 500/14 gerecht werden. Es gibt sie in verschiedenen Ausführungen. Informieren Sie sich auf der Webseite des Herstellers

Version 3: OEM2 with Support Bolt

The OEM2 axle plate can be used in two versions with a support screw:

  1. The frame has a disc brake mount, but no disc brake is installed. Use M6 screw.
  2. The frame has an M5 luggage carrier thread and the distance to the center of the axle is 39.9 mm. Use OEM2 adapter with M5 screw.

Both versions have in common the position behind the imaginary line through the axle slot. In addition, both need the distance to the center of the axle of 39.9 mm. The exact dimensions are shown on the technical drawing OA47.

Support screw through disc brake mount

The support bolt assembly for OEM2 mounting consists of a bolt (M6x16), a washer and a locknut.

It is secured through the disc brake mounting hole of the dropout from the inside (tightening torque: 8Nm/71in.lbs.).

Mounted support bolt, view from inside the frame: From the inside of the frame, a bolt has is inserted into the lower disc brake caliper mounting point. The axle plate CC/TS-OEM2 can lock itself around this bolt.

Mounted support bolt, view from outside the Frame.

Frames with International Standard (IS-1999) disc brake mounts.

If the disc brake mount on the frame is used to anchor the SPEEDHUB torque, then this area must have the following dimensions.

If the above dimensions are kept and the frame material is faultless, the manufacturer may safely install the Rohloff SPEEDHUB 500/14, as described here for version 3 and version 4. The technical OEM2 data sheet must be referred to when using this product!

Furthermore, it is necessary to grant retailers permission to use this method of supporting the output torque produced by the Rohloff SPEEDHUB 500/14! You can download the corresponding form from the following link:

Download

Dropout with disc brake mount (International Standard IS-1999)

Axle plate CC/TS-OEM2 and Bolt with washer and self-locking nut

The OEM2 axleplate cannot be used to mount a Rohloff SPEEDHUB 500/14 into frames with vertical dropout slots where the IS or Postmount disc brake mount is positioned on the chainstay.

Support Screw through Luggage Carrier Thread

The OEM2 axle plate can also be used when an additional hole is positioned in the dropout behind a vertical line through the axle. This hole must accept an M6 bolt or an M5 bolt in combination with our M5-OEM2 adapter (Article #8552).

Ideally, a drilled & tapped luggage/fender mount hole can be located in the correct position (39,9mm) from the axle center and thus ensuring each frame is SPEEDHUB compatible using Art.#8552, even if not primarily sold with the SPEEDHUB option.

Adapter OEM2 for M5 screw (Article No. 8552)

See also axle plate accessories in our B2B shop.

Important: An M5 cylinder head is only 8 mm in diameter, therefore an M5 screw must not be used without the OEM2 adapter with a diameter of 10 mm (Article No. 8552).

Version 4: OEM2 with Disc Brake

OEM2 axle plate; bicycle frame with disc brake mounts of International Standard (IS-1999)*, and a mounted disc brake.

Dropout with disc brake mount (International Standard IS-1999): If a disc brake is mounted, the torque can be anchored to the frame using the CC OEM2 or TS OEM2 axleplate, in conjunction with either the SPEEDBONE or Monkeybone.

*Dimension information: Dropouts built to International Standard IS-1999 feature 16.3mm distance between the inner face of the dropout and the brake disc itself.

Mounting the OEM2 axleplate with SPEEDBONE and External Gear Mech.

See technical drawing OA79 in our drawing set.

Mounting the OEM2 axleplate with SPEEDBONE and External Gear Mech coming from top

Accessories for assembly using OEM2 axle plate and SPEEDBONE

Link to axle plates etc. in our B2B shop

Mounting the OEM2 axleplate with Monkeybone for 160mm or 180mm

The ROHLOFF SPEEDHUB 500/14 can also be fitted on full suspension frames which feature a ‘Horst-Link’ and disc brake mounts (International Standard IS-1999) by using an OEM2 axleplate together with a SPEEDBONE or Monkeybone.

Frames with International Standard (IS-1999) disc brake mounts.

If the disc brake mount on the frame is used to anchor the SPEEDHUB torque, then this area must have the following dimensions.

If the above dimensions are kept and the frame material is faultless, the manufacturer may safely install the Rohloff SPEEDHUB 500/14, as described here for version 3 and version 4. The technical OEM2 data sheet must be referred to when using this product!

Furthermore, it is necessary to grant retailers permission to use this method of supporting the output torque produced by the Rohloff SPEEDHUB 500/14! You can download the corresponding form from the following link:

Download

Version 5: Postmount direct

Frames with a Postmount (PM) direct caliper mount: The Rohloff PM Axleplate in combination with the PM Bone offers an alternative method of anchoring the hub torque to frames with a 135mm, 142mm, 148mm, 170mm or 177mm spacing. The PM Axleplate/PM Bone combination is recommended when mounting a SPEEDHUB to frames with an integrated Postmount direct caliper mount. The threaded holes of the direct caliper mount will be used to secure the PM Bone.

See also the corresponding chapter in our Speedhub manual.

Mounting on frame with a Postmount (PM) direct caliper mount on the seat stay

Mounting on frame with a Postmount (PM) direct caliper mount on the chain stay

Version 6: 12mm Thru-axle Frames

The installation conditions for 12mm thru axle frames can be found in our compatibility check for equipping a 12mm thru axle frame (142/148/177/197mm) with a Rohloff SPEEDHUB A12 hub: just click here

Here you can see one of the A12 SPEEDHUB variants with PM Bone and PM Axleplate

Gear Mech

E-14 Shifter Unit

The Rohloff E-14 is the electronic shifting system for e-bikes combined with the Rohloff SPEEDHUB 500/14. You can find detailed information about the Rohloff E-14 here in our manual.

The Rohloff E-14 shifter unit, combined with the Rohloff SPEEDHUB 500/14, works in unison with Bosch and Panasonic FIT eBike transmissions to provide an optimally coordinated shift between gears.

This in turn increases both the rider comfort, safety and battery range while simultaneously drastically reducing the wear of all bicycle transmission components.

External Gear Mechanism

The Rohloff SPEEDHUB 500/14 is controlled via the external gear mech. The external transfer box must be positioned so that an optimal cable routing is achieved. The shifting box can be rotated in 30° increments to achieve this perfect cable routing.

Pointer

Cables should be routed as close to the pivot point as possible when mounting a Rohloff SPEEDHUB 500/14 into a full-suspension bike. This helps reduce the additional friction created in the cables as they try to move as the rear triangle is activated.

External Gear Mechanism with Rohloff SPEEDHUB 500/14 CC DB OEM or TS DB OEM

Generally we recommend routing the cables along the downtube and chainstay.

Spokes

Spoke lengths

The Rohloff SPEEDHUB 500/14 is available with either 32, or 36 spoke holes forming a hole diameter of 100mm. 26“-wheels therefore, require shorter spokes which are slightly more difficult to source.

Along with the SPEEDHUB, we are also able to provide Sapim Race spokes 2.0/1.8/2.0mm with spoke bend length 2.9mm in all even lengths between 220mm and 282mm. These are available in silver and black.

Small wheels

Wheels smaller than 26“ must be laced using a single cross lacing pattern in order to guarantee the spokes will have the correct angle of entry to the rim. Radial lacing the Rohloff SPEEDHUB 500/14 is not permitted!

The Rohloff SPEEDHUB 500/14 should not be used with rims smaller than 18“ as the angle between rim and the high hub flange would become to acute, causing spokes to kink where they enter the nipples leading to premature spoke failure.

The table below shows the required spoke lengths for the most commonly used ERD values. As the hub flange is symmetric, all spokes required for lacing the Rohloff SPEEDHUB 500/14 will be the same length:

32-hole Hub-shell Spoke lengths

*ERD: Effective Rim Diameter
Wheel Size Number of
Spoke Crosses
ERD* 32-hole
Spoke lengths
18" 1 341-343 128
    344 130
20" 1 372-373 142
    374-377 144
    378-381 146
    382-385 148
    386-389 150
    390-394 152
24" 1 472-476 192
    477-480 194
    481-484 196
    485-489 198
    490-493 200
    494-497 202
    498-501 204
    502-503 206
26" 2 516-519 226
    520-523 228
    524-527 230
    528-531 232
    532-535 234
    536-539 236
    540-543 238
    544-547 240
    548-551 242
    552-555 244
650B 2X 556-559 246
    560-563 248
    564-567 250
    568-571 252
    572-575 254
    576-579 256
    580-583 258
28" 2 584-587 260
    588-592 262
    593-596 264
    597-600 266
    601-604 268
    605-608 270
29" 2 609-612 272
    613-616 274
    617-620 276
    621-624 278
    625-628 280
    629-632 282

36-hole Hub-shell Spoke lengths

*ERD: Effective Rim Diameter
Wheel Size Number of
Spoke Crosses
ERD* 36-hole
Spoke lengths
18" 1 341-342 126
    343-344 128
20" 1 372-375 142
    376-379 144
    380-383 146
    384-387 148
    388-392 150
    393-396 152
24" 1 472-474 190
    475-478 192
    479-482 194
    483-486 196
    487-490 198
    491-494 200
    495-498 202
    499-502 204
    503 206
26" 2 516-517 222
    518-522 224
    523-526 226
    527-530 228
    531-534 230
    535-538 232
    539-542 234
    543-546 236
    547-550 238
    551-554 240
    555-558 242
    559-562 244
650B 2 563-566 246
    567-570 248
    571-574 250
    575-578 252
    579-582 254
28" 2 583-586 256
    587-590 258
    591-594 260
    595-598 262
    599-602 264
    603-607 266
29" 2 608-611 268
    612-615 270
    616-619 272
    620-623 274
    624-627 276
    628-631 278

Wheel stability

The Rohloff SPEEDHUB 500/14, when laced into a 32 or 36 spoke rim, will create a stronger wheel than a traditional dished derailleur hub wheel.
The SPEEDHUB 500/14 wheel stability corresponds to that of a Tandem wheel with 48 spokes!

The spoke flanges of the Rohloff SPEEDHUB 500/14 are symmetrical. The rim is therefore centrally placed between the hub flanges, the spokes radiate from both sides of the hub at an equal angle to the rim and the resulting wheel is not dished. All spokes from a Rohloff SPEEDHUB 500/14 wheel will therefore be of the same length and should have exactly the same spoke tension (min. 1000-1300N).

To build a strong, long lasting wheel, quality spokes should be pre-tensioned with a minimum tension of 1000N (measured with an inflated tire) or 1300N (measured without a tire fitted). This value cannot always be reached with an un-dished wheel, because the spokes on the sprocket side of the hub have to be tensioned to around 1475N which can cause problems with the nipple seat at the rim. The spoke tension on an 8-speed cassette hub is usually only 600N on the opposing flange side. See the comparison to an MTB 8-speed wheel overleaf.

Because of the larger diameter hub flange, the spokes have, despite only being double crossed, approximately the same angle to the rim as the spokes of a triple cross laced wheel with a low-flange hub. Due to the fact that the spokes coming from the Rohloff SPEEDHUB 500/14 radiate from a larger circle, they are not subjected to the same amounts of stress. It therefore follows that the force passed on to the rim is far less, in comparison to that passed on by the spokes of a traditional low-flange hub (Torque = Force x Lever).

• Spokes with a 2.9mm Neck/J-bend MUST be used when lacing SPEEDHUB wheels!
Double butted spokes from quality manufacturers such as SAPIM and DT-Swiss, were supplied with a 2.9mm neck/J-bend as standard, up until 2015. This standard dimension was thereafter reduced to 2.6mm. A spoke neck/J-bend of less than 2.9mm will apply excessive forces to the SPEEDHUB flange which will lead to flange failure over time.
It is imperative that OEM bicycle manufacturers source quality spokes with a 2.9mm neck/J-bend for lacing SPEEDHUB wheels!

Comparison of spoke tensions

Comparison of maximum occurring spoke tensions measured during our tests.
Values in brackets show spoke tension with quality spokes and an inflated tire.

Comparison with MTB

Wheel with SPEEDHUB 500/14, 32 spokes
Wheel with 8-speed derailleur gear, 36 spokes
Driver 80kg, pedalling while standing on the pedals.
Transmission SPEEDHUB: 4th gear (48/16)
Spread: 2,52m
Transmission derailleur gear: 36/30
Spread: 2,47m

Comparison with Tandem

Wheel with SPEEDHUB 500/14, 32 spokes
Wheel with 8-speed derailleur gear, 48 spokes
2 riders of 80kg, pedalling while standing on the
pedals.
Transmission SPEEDHUB: 4th gear (48/16)
Spread: 2,52m
Transmission derailleur gear: 36/30
Spread: 2,47m

The values for the Tandem 8-speed hub turn out more favorable despite there being 2 riders, because there are 48 spokes and because more symmetric flange width than the values for the MTB wheel. However, the values of the Rohloff SPEEDHUB 500/14 wheel are, with 1.206N in comparison to 1.409N, still better.

Rohloff SPEEDHUB 500/14 on Tandems

All versions of the Rohloff SPEEDHUB 500/14 are certified for tandem use long as the frame spacing remains 135, 142, 148, 170, 177, 190, 197mm. The Article number/description is extended by the appendix ‘T’ (Example: CC-T or TS-EX-T).

All SPEEDHUB 500/14 versions are supplied with spoke holes of 2.7mm and are drilled for either 32 or 36 spokes. The tandem versions differ to the regular Rohloff SPEEDHUB 500/14 only through the length of cable supplied in the kit. All tandem versions are supplied with cables of 2.8m in length. As the only difference is the cable length, these hubs are also suitable for recumbents, HPVs and other applications where longer cables are required.

A special, reinforced CC OEM Tandem Axleplate (Art. #8234T) is also available upon request. This Axleplate permits only one mounting orientation.

General Info about the Drive

The hub will be delivered from us with a 16-tooth steel sprocket and standard splined carrier, unless otherwise requested sizes (13, 14), 15, 17, 18, 19 and 21 teeth are also available, as is the option of a no sprocket (Carbon Drive applications with carrier L) or slim splined carrier). We recommend front chainrings with a size of 38, 42, 44 or 46 teeth, depending on how the bike will be used. We offer a special sprocket with 13 or 14 teeth for use with the Rohloff SPEEDHUB 500/14 on bikes with small rear wheels (for example 20“ recumbent or folding bicycles). By using this sprocket, a greater overall gear ratio can be achieved even with this size wheel. The chainline of all splined sprockets used on 135mm/142mm SPEEEDHUB units, is 58mm when mounted to a standard splined carrier, or 55mm when mounted to a slim splined carrier. All splined sprockets are designed as reversible sprockets.

The Rohloff SPEEDHUB 500/14 is constructed for use in races, the high loads which arise during races are therefore not sufficient to overload the Rohloff SPEEDHUB 500/14. The high gear-ratio (for example 42/16) transforms the low revolutions at the crank to higher revolutions at the rear sprocket and thereby reduces the input torque for the hub. For safety reasons and in order to guarantee that the SPEEDHUB gear-unit cannot be overloaded, there are certain primary transmission ratios which may not be undercut. The lowest permitted gear ratios (transmission factor 1.9 for solo cyclists under 100kg) are 32:17, 30:16, 28:15 and 39:13 = transmission factor 3.0 when mounted in a normal bicycle (i.e. not a tandem). The smallest gear of the Rohloff SPEEDHUB 500/14 corresponds in each case to a 20:40 ratio with derailleur gears. There are no upper limits concerning the choice of the chainring size.

The lowest permitted sprocket ratios for the Gates Carbon drive system can be found at: Manual for the Gates Carbon Drive™ System used with theRohloff SPEEDHUB 500/14

Min. primary transmission factor
Solo cyclists under 100 kg = 1.9
Tandem, Cargo, Recumbent applications or cyclists over 100 kg = 2.5 (in table highlighted in bold)
Sprockets 13 or 14 teeth = 3.0* (in table highlighted in bold)

*A higher factor of 3.0 has been introduced for 13 and 14 tooth sprockets, for all areas of application, to protect against overloading.

Last update: 19/05/2021

Entfaltung/Übersetzung

Primary Transmission Factors for mid-motor eBikes

Vehicle type Primary Transmission Factor max. Input Torque at
SPEEDHUB Sprocket*
EU Approved
eBike Motor**
Non EU Approved
eBike Motor***
max.
System Weight
max.
Wheel Load
Solo Bicycle
Rider weight = ≤100kg
1.9 130 Nm ✔️ ✔️ 250 kg 150 kg
Tandem
Rider weight = >100kg
2.5 130 Nm ✔️ 250 kg 150 kg
Cargo / Recumbent
SPEEDHUB located in wheel
2.5 130 Nm ✔️ 250 kg 150 kg
Cargo / Recumbent
SPEEDHUB located in wheel
3.0 130 Nm ✔️ >250 kg 150 kg
Cargo / Recumbent
SPEEDHUB located in frame
2.5 130 Nm ✔️ 250 kg ---
Cargo / Recumbent
SPEEDHUB located in frame
3.0 130 Nm ✔️ >250 kg ---

✔️  Approved and Authorized for SPEEDHUB use    
❌ Non approved / Not authorized for SPEEDHUB use    
* 130Nm input = force created by rider, plus motor, divided by Primary Transmission Factor (PTF)

e.g.:    

  • Rider creates 150Nm. Motor creates 100Nm. PTF of 2.5 = 150+100 = 250/2.5 = 100 (100Nm = OK).
  • Rider creates 250Nm. Motor creates 100Nm. PTF of 2.5 = 250+100 = 350/2.5 = 140 (140Nm = NOT OK).

** Max. 250W Nominal Power / Max. 800W Peak Power    
*** Max. > 250W Nominal Power / Max. > 800W Peak Power    

Distance traveled per crank revolution with 20'' wheels (circumference 1.51 m). In the top row are the sprockets, in the left column the corresponding chainring. Details from-to in meters per crank turn.

  13 teeth 14 teeth 15 teeth 16 teeth 17 teeth 18 teeth 19 teeth 21 teeth
28 teeth     0.79 - 4.13          
30 teeth     0.84 - 4.43 0.79 - 4.15        
32 teeth     0.90 - 4.73 0.84 - 4.43 0.79 - 4.17      
34 teeth     0.95 - 5.02 0.90 - 4.71 0.84 - 4.43 0.80 - 4.18    
36 teeth     1.01 - 5.32 0.95 - 4.98 0.89 - 4.69 0.84 - 4.43 0.80 - 4.20  
38 teeth     1.07 - 5.61 1.00 - 5.26 0.94 - 4.95 0.89 - 4.68 0.84 - 4.43  
40 teeth 1.30 - 6.82   1.12 - 5.91 1.05 - 5.54 0.99 - 5.21 0.94 - 4.92 0.89 - 4.66 0.80 - 4.22
42 teeth 1.36 - 7.16 1.26 - 6.65 1.18 - 6.20 1.11 - 5.81 1.04 - 5.47 0.98 - 5.17 0.93 - 4.90 0.84 - 4.43
44 teeth 1.43 - 7.50 1.32 - 6.96 1.24 - 6.50 1.16 - 6.09 1.09 - 5.73 1.03 - 5.41 0.98 - 5.13 0.88 - 4.64
46 teeth 1.49 - 7.84 1.38 - 7.28 1.29 - 6.79 1.21 - 6.37 1.14 - 5.99 1.08 - 5.66 1.02 - 5.36 0.92 - 4.85
48 teeth 1.56 - 8.18 1.44 - 7.59 1.35 - 7.09 1.26 - 6.65 1.19 - 6.25 1.12 - 5.91 1.06 - 5.60 0.96 - 5.06
50 teeth 1.62 - 8.52 1.50 - 7.91 1.40 - 7.38 1.32 - 6.92 1.24 - 6.52 1.17 - 6.15 1.11 - 5.83 1.00 - 5.27
52 teeth 1.69 - 8.86 1.56 - 8.23 1.46 - 7.68 1.37 - 7.20 1.29 - 6.78 1.22 - 6.40 1.15 - 6.06 1.04 - 5.49
54 teeth 1.75 - 9.20 1.62 - 8.54 1.52 - 7.97 1.42 - 7.48 1.34 - 7.04 1.26 - 6.65 1.20 - 6.30 1.08 - 5.70
56 teeth 1.81 - 9.54 1.69 - 8.86 1.57 - 8.27 1.47 - 7.75 1.39 - 7.30 1.31 - 6.89 1.24 - 6.53 1.12 - 5.91

Distance traveled per crank revolution with 26'' wheels (circumference 1.51 m). In the top row are the sprockets, in the left column the corresponding chainring. Details from-to in meters per crank turn.

  13 teeth 14 teeth 15 teeth 16 teeth 17 teeth 18 teeth 19 teeth 21 teeth
28 teeth     1.07 - 5.64          
30 teeth     1.15 - 6.04 1.08 - 5.67        
32 teeth     1.23 - 6.45 1.15 - 6.04 1.08 - 5.69      
34 teeth     1.30 - 6.85 1.22 - 6.42 1.15 - 6.04 1.09 - 5.71    
36 teeth     1.38 - 7.25 1.29 - 6.80 1.22 - 6.40 1.15 - 6.04 1.09 - 5.73  
38 teeth     1.46 - 7.66 1.37 - 7.18 1.28 - 6.76 1.21 - 6.38 1.15 - 6.04  
40 teeth 1.77 - 9.30   1.53 - 8.06 1.44 - 7.56 1.35 - 7.11 1.28 - 6.72 1.21 - 6.36 1.09 - 5.76
42 teeth 1.86 - 9.76 1.72 - 9.07 1.61 - 8.46 1.51 - 7.93 1.42 - 7.47 1.34 - 7.05 1.27 - 6.68 1.15 - 6.04
44 teeth 1.95 - 10.23 1.81 - 9.50 1.69 - 8.86 1.58 - 8.31 1.49 - 7.82 1.40 - 7.39 1.33 - 7.00 1.20 - 6.33
46 teeth 2.03 - 10.69 1.89 - 9.93 1.76 - 9.27 1.65 - 8.69 1.56 - 8.18 1.47 - 7.72 1.39 - 7.32 1.26 - 6.62
48 teeth 2.12 - 11.16 1.97 - 10.36 1.84 - 9.67 1.72 - 9.07 1.62 - 8.53 1.53 - 8.06 1.45 - 7.63 1.31 - 6.91

Distance traveled per crank revolution with 650B wheels (circumference 2.15 m). In the top row are the sprockets, in the left column the corresponding chainring. Details from-to in meters per crank turn.

  13 teeth 14 teeth 15 teeth 16 teeth 17 teeth 18 teeth 19 teeth 21 teeth
28 teeth     1.12 - 5.89          
30 teeth     1.20 - 6.31 1.12 - 5.91        
32 teeth     1.28 - 6.73 1.20 - 6.31 1.13 - 5.94      
34 teeth     1.36 - 7.15 1.27 - 6.70 1.20 - 6.31 1.13 - 5.96    
36 teeth     1.44 - 7.57 1.35 - 7.10 1.27 - 6.68 1.20 - 6.31 1.14 - 5.98  
38 teeth     1.52 - 7.99 1.42 - 7.49 1.34 - 7.05 1.27 - 6.66 1.20 - 6.31  
40 teeth 1.85 - 9.70   1.60 - 8.41 1.50 - 7.89 1.41 - 7.42 1.33 - 7.01 1.26 - 6.64 1.14 - 6.01
42 teeth 1.94 -10.19 1.80 - 9.46 1.68 - 8.83 1.57 - 8.28 1.48 - 7.79 1.40 - 7.36 1.33 - 6.97 1.20 - 6.31
44 teeth 2.03 -10.68 1.89 - 9.91 1.76 - 9.25 1.65 - 8.67 1.55 - 8.16 1.47 - 7.71 1.39 - 7.30 1.26 - 6.61
46 teeth 2.12 -11.16 1.97 -10.36 1.84 - 9.67 1.72 - 9.07 1.62 - 8.53 1.53 - 8.06 1.45 - 7.64 1.31 - 6.91
48 teeth 2.21 -11.65 2.06 -10.81 1.92 -10.09 1.80 - 9.46 1.69 - 8.91 1.60 - 8.41 1.52 - 7.97 1.37 - 7.21

Distance traveled per crank revolution with 28'' wheels (circumference 2.18 m). In the top row are the sprockets, in the left column the corresponding chainring. Details from-to in meters per crank turn.

  13 teeth 14 teeth 15 teeth 16 teeth 17 teeth 18 teeth 19 teeth 21 teeth
28 teeth     1.14 - 5.97          
30 teeth     1.22 - 6.40 1.22 - 6.40        
32 teeth     1.30 - 6.82 1.22 - 6.40 1.14 - 6.02      
34 teeth     1.38 - 7.25 1.29 - 6.80 1.22 - 6.40 1.15 - 6.04    
36 teeth     1.46 - 7.68 1.37 - 7.20 1.29 - 6.77 1.22 - 6.40 1.15 - 6.06  
38 teeth     1.54 - 8.10 1.44 - 7.60 1.36 - 7.15 1.28 - 6.75 1.22 - 6.40  
40 teeth 1.87 - 9.84   1.62 - 8.53 1.52 - 8.00 1.43 - 7.52 1.35 - 7.11 1.28 - 6.73 1.16 - 6.09
42 teeth 1.97 - 10.33 1.82 - 9.59 1.70 - 8.95 1.60 - 8.39 1.50 - 7.90 1.42 - 7.46 1.34 - 7.07 1.22 - 6.40
44 teeth 2.06 - 10.82 1.91 - 10.05 1.78 - 9.38 1.67 - 8.79 1.57 - 8.28 1.49 - 7.82 1.41 - 7.41 1.27 - 6.70
46 teeth 2.15 - 11.32 2.00 - 10.51 1.87 - 9.81 1.75 - 9.19 1.65 - 8.65 1.55- 8.17 1.47 - 7.74 1.33 - 7.01
48 teeth 2.25 - 11.81 2.09 - 10.96 1.95 - 10.23 1.82 - 9.59 1.72 - 9.03 1.62 - 8.53 1.54 - 8.08 1.39 - 7.31
50 teeth 2.34 - 12.30 2.17 - 11.42 2.03 - 10.66 1.90 - 9.99 1.79 - 9.41 1.69 - 8.88 1.60 - 8.42 1.45 - 7.61

Distance traveled per crank revolution with 29'' wheels (circumference 2.30 m). In the top row are the sprockets, in the left column the corresponding chainring. Details from-to in meters per crank turn.

  13 teeth 14 teeth 15 teeth 16 teeth 17 teeth 18 teeth 19 teeth 21 teeth
28 teeth     1.20 - 6.30          
30 teeth     1.28 - 6.75 1.20 - 6.33        
32 teeth     1.37 - 7.20 1.28 - 6.75 1.21 - 6.35      
34 teeth     1.45 - 7.65 1.36 - 7.17 1.28 - 6.75 1.21 - 6.37    
36 teeth     1.54 - 8.10 1.44 - 7.59 1.36 - 7.15 1.28 - 6.75 1.22 - 6.39  
38 teeth     1.63 - 8.55 1.52 - 8.01 1.43 - 7.54 1.35 - 7.12 1.28 - 6.75  
40 teeth 1.97 - 10.38   1.71 - 9.00 1.60 - 8.44 1.51 - 7.94 1.43 - 7.50 1.35 - 7.10 1.22 - 6.43
42 teeth 2.07 - 10.90 1.93 - 10.12 1.80 - 9.45 1.68 - 8.86 1.59 - 8.34 1.50 - 7.87 1.42 - 7.46 1.28 - 6.75
44 teeth 2.17 - 11.42 2.02 - 10.60 1.88 - 9.90 1.76 - 9.28 1.66 - 8.73 1.57 - 8.25 1.49 - 7.81 1.34 - 7.07

Distance traveled per crank revolution with 26'' Fatbikes (circumference 2.32 m). In the top row are the sprockets, in the left column the corresponding chainring. Details from-to in meters per crank turn.

  13 teeth 14 teeth 15 teeth 16 teeth 17 teeth 18 teeth 19 teeth 21 teeth
28 teeth     1.21 - 6.35          
30 teeth     1.29 - 6.81 1.21 - 6.38        
32 teeth     1.38 - 7.26 1.29 - 6.81 1.22 - 6.41      
34 teeth     1.47 - 7.71 1.38 - 7.23 1.29 - 6.81 1.22 - 6.43    
36 teeth     1.55 - 8.17 1.46 - 7.66 1.37 - 7.21 1.29 - 6.81 1.23 - 6.45  
38 teeth     1.64 - 8.62 1.54 - 8.08 1.45 - 7.61 1.37 - 7.19 1.29 - 6.81  
40 teeth 1.99 - 10.47   1.73 - 9.08 1.62 - 8.51 1.52 - 8.01 1.44 - 7.56 1.36 - 7.17 1.23 - 6.48
42 teeth 2.09 - 11.00 1.94 - 10.21 1.81 - 9.53 1.70 - 8.93 1.60 - 8.41 1.51 - 7.94 1.43 - 7.52 1.29 - 6.81
44 teeth 2.19 - 11.52 2.03 - 10.70 1.90 - 9.98 1.78 - 9.36 1.68 - 8.81 1.58 - 8.32 1.50 - 7.88 1.36 - 7.13
46 teeth 2.29 - 12.04 2.13 - 11.18 1.98 - 10.44 1.86 - 9.78 1.75 - 9.21 1.65 - 8.70 1.57 - 8.24 1.42 - 7.46
48 teeth 2.39 - 12.57 2.22 - 11.67 2.07 - 10.89 1.94 - 10.21 1.83 - 9.61 1.73 - 9.08 1.64 - 8.60 1.48 - 7.78

Comination with electric motors

The motor needs to be programmed to reduce power when cranks are at the dead point (12:00 and 6:00 o'clock positions) as well as to not exceed the maximum 130Nm input torque value at the rear sprocket. The SPEEDHUB 500/14 is a force dependent transmission so if the additional force of a motor is not reduced at the crank dead-point, then the internal shifting elements will not be able to function correctly. This will result in a harsh shift, far from comfortable for the cyclist. The Rohloff AG will require all the technical data over the transmission in order to permit the SPEEDHUB for use in the Pedalec/electric bicycle.

Use with two chain rings

It is possible to use two chainrings, a front derailleur and a handlebar shifter in order to extend the gear ratio for extreme use. Please regard that the chainrings must possess a tooth difference of 13% in order to actually create one additional gear, or approximately 29% for two additional gears. When for example, you use a 50-tooth chainring and an additional 39-tooth chainring, the total transmission range would result in 678 %.

Chainline

The optimum chainline for a 135mm/142mm Rohloff SPEEDHUB 500/14 with sprockets of 15, 16, 17, 18, 19 & 21 teeth is 55mm (splined carrier slim - S). The optimum chainline with sprockets of 13, 14, 15, 16, 17, 18, 19 & 21 teeth is 58mm (Splined Carrier - Standard) measured from the center of the frame.

Accessories

Chain Tension

An external chain tensioner is necessary for frames where there is no other possibility to tension the chain (i.e. via an adjustable dropout, a dropout with a long slot, or an EBB). A chain tensioner is also required with dropouts where the axle has less than 25mm room for adjustment (fig. 20). This also refers to bikes with rear suspension (except models with transmission swing arms), as the chain length changes as the rear shock is activated. The tension capacity of our chain tensioner is 10 links.

Adjustment of chain length using an EBB (min. 13mm adjustability) in combination with an OEM dropout.

Dropout with torque support axle plate OEM

Adjustment of chain length using an EBB (min 13mm) in combination with a standard dropout with disc brake mounts (IS-1999) and an OEM2 axleplate.

Dropouts with adjustment room > 25 mm - an external chain tensioner is not necessary.
Dropouts with adjustment room < 25 mm - an external chain tensioner will be required!

Use of a Disc Brake (DB)

Disc Brake versions of the Rohloff SPEEDHUB 500/14 are fitted with a special hub cap and an External Gear Mech. The flange of the hub cap has 4 tapped holes M8x0.75 onto which the brake rotor can be mounted. Only brake rotors with a special 4-bolt pattern for the Rohloff SPEEDHUB 500/14 can be used, (65mm diameter bolt diameter, inner circle diameter 52 mm).

The Rohloff AG is able to offer (at time of press) suitable brake discs for:

160/2,0mm for Magura (Art. #8282)
180/2,0mm for Magura (Art. #8283)
203/2,0mm for Magura (Art. #8284)
160/1,8mm for Shimano, Hayes, Formula, Avid (Art. #8281)
180/1,8mm for Shimano, Formula, Hayes, Avid (Art. #8287)
203/1,8mm for Hayes, Shimano, Avid (Art. #8286)

Magura, Avid, Hope and Formula can deliver manufacturers with disc brake packages direct with the corresponding rear disc.

Contact the brake manufacturer directly for compatibility information regarding brands other than those listed above. Brake rotors with a diameter smaller than 150mm are incompatible as the caliper will collide with the SPEEDHUB shell itself.

Chain Guide

Rohloff also offers a chain guide that may be mounted additionally. This is necessary on full-suspension bikes and bikes used for hard cross-country riding should also have a chain guide in order to prevent the chain from jumping off of the chainring. We would actually advise this component is mounted to all bikes that use a spring loaded, self-adjusting chain tensioning system.

Chain guide Rohloff SPEEDHUB 500/14

Trailer Hitch

Use of a trailer hitch in conjunction with a Rohloff SPEEDHUB 500/14 is generally not a problem as long as one ensures that neither trailer nor hitch collide with any Rohloff component during a ride. This is especially important when used with an E-14 equipped SPEEDHUB unit. The E-.14 shifter unit has a plastic cap which can easily be deformed when pressure is applied by colliding with trailer hitches. The pressure may deform the cap and compromise the seal quality of this component!

Use of washers/spacers or special adapters offered by the trailer hitch manufacturer should be used if necessary, to ensure enough clearance between the two components and thus avoid the sort of damage outlined above.

ATTENTION:
Bicycle trailer hitches which mount directly to the 12mm thru-axlemust not be used in conjunction with an A12 SPEEDHUB 500/14 unit. The additional thickness of the trailer hitch will hinder the specially produced M7 mounting bolt (increased stiffness) from penetrating the SPEEDHUB axle or axleplate deep enough. Threads will be stripped as there are not enough to adequately ensure the SPEEDHUB is mounted safely into the frame. A loose, insufficiently secured SPEEDHUB could lead to accidents and injuries so must be avoided.

Package Contents

The OEM SPEEDHUB will be supplied in non-branded, OEM packaging and comes assembled with the correct axleplate, a standard splined carrier and 16 tooth sprocket (13, 15, 17, 18, 19 or 21-tooth sprocket or slim splined carrier as options).

If ordering a Gates Carbon Drive compatible SPEEDHUB, the splined sprocket carrier will be replaced with the lock-ring splined carrier (Art. #8540L). Supply of such hubs will only be supplied to manufacturers for fitting into a stiffness test approved frames. We will require a copy of the test protocol before we are able to supply these products.

The Carbon Drive sprocket will need to be secured to the lock-ring carrier, be tightening the lock-ring to 30Nm using the Rohloff Lock-Ring Tool (Art.#8518).

OEM supplied SPEEDHUBs are dispatched to EU addresses, pre-filled with SPEEDHUB all-season-oil (green flyer included in hub documentation)!

Also contained in the package are all components required for the respective hub version:

  • twist shifter,
  • gear cables in the required length (225 cm and/or 305 cm)
  • internal cable routing
  • bayonet fixing
  • cable guide
  • external cable box etc.

Also included in a clear plastic bag for the consumer are:

  • Owners Manual,
  • Warranty Card
  • Information on the Rohloff SPEEDHUB 500/14.

These last 3 items must be forwarded to the consumer when the complete bicycle is shipped.

Operating Instructions

Maintenance

In comparison to a derailleur gear system, the Rohloff SPEEDHUB 500/14 is relatively maintenance-free. The internal gearing runs encapsulated in an oil bath; it is protected by seals against dirt and moisture and is completely maintenance-free. All bearings are either sealed cartridge bearings or run also inside the hub within the oil bath. Therefore, maintenance of the Rohloff SPEEDHUB 500/14 is reduced to an annual oil change.

The indexed gearing of the Rohloff SPEEDHUB 500/14 is located directly within the hub.The cable tension has no effect on the gear shift precision.

On the Rohloff SPEEDHUB 500/14 the chain is running straight and is only driven by one large chainring. Therefore, the wear on the drive chain is fundamentally lower than with a comparable derailleur system.

Brake-in Period

All gears and coupling elements of the Rohloff SPEEDHUB 500/14 are manufactured from hardened steel and are machined to a high precision. The break-in period is approximately 1.000km due to the high wear resistance of all parts. The gears get finally smoothened out by the moving of the parts under pedaling force. The result of this process is less operational noise and a much smoother operation. The hub shell of the Rohloff SPEEDHUB 500/14 has specially constructed seals. These also take about 1.000 km to break-in; it is quite normal with a new hub, for the cranks to rotate when the bicycle is pushed, this is because the new hub seals force the sprocket to rotate with the hub. This effect recedes over time and has no influence upon riding comfort.

Operational Noise

On the Rohloff SPEEDHUB 500/14 three sets of planetary gears work in line to achieve 14 different speeds. The first two sets of planet gears produce seven gears (8th to 14th). When these seven gears are set against the third set of planet gears, then gears from 1st to 7th are produced. The third set of planetary gears rotate at extreme speeds, the highest RPM being in the 7th gear. The rotation of these planetary gears can be heard as a humming noise which is transmitted via the axle into the frame. Depending on frame type, material and other components fitted around the axle (fenders, luggage racks, kickstand etc) this noise is either more or less audible. The more the hub is ridden, the quieter these noises become. These high RPM planetary gears are not in use and the upper 7 speeds and the result is an almost silently running SPEEDHUB.

When coasting along, different freewheels may work depending on the gear selected. This too can result in different noises.

Oil Change

The Rohloff SPEEDHUB 500/14 is filled with 25ml of special gear oil (all season oil). This ensures:

  • moving parts lubricated,
  • steel parts protected from corrosion,
  • freewheeling and gear noises subdued.

Gates Carbon Drive

The following points must be addressed and adhered to when mounting the Rohloff SPEEDHUB 500/14 together with a Gates Carbon Drive system. Failure to adhere to these points will result in partial loss of guarantee and warranty cover of the SPEEDHUB 500/14.

1. Manufacturers conditions/instructions for use

Read the Owners Manual for both Gates Carbon Drive and the Rohloff SPEEDHUB 500/14 and ensure these products are correctly implemented on the bicycle as described within the manuals: Manual for the Gates Carbon Drive™ System used with theRohloff SPEEDHUB 500/14

2. Frame Approval

Safe operation of a SPEEDHUB using Gates Carbon Drive system is only possible if the frames reartriangle retains a minimum stiffness level. Frame manufacturers must prove frame stiffness levels on a specialist testing jig in order to receive type approval for SPEEDHUB use.

A list of approved frames can be found online under the link below:
Carbon Drive stiffness test approved bicycle frames

Please enquire with the frame manufacturer directly should your chosen bicycle frame not be listed.

Universal Transmissions (Gates Carbon Drive EU distribution) are able to issue frame certifications on an individual basis should you still wish to use that particular frame.
Frame testing for Rohloff SPEEDHUB 500/14

3. Use of a Snubber

The Rohloff AG insist that a Snubber is additionally mounted to the bicycle. A Snubber prevents the belt from ratcheting over sprocket teeth when belt tension is lost. Subsequently this small component greatly reduces the accident risk level. Please enquire with the frame manufacturer directly should your chosen bicycle not be fitted with a Snubber.

Information for Europe

Universal Transmissions GmbH
ATTN: Chris Harris
Walkmühlenstr. 194
99974 Mülhausen
Germany

Telefon: +49 3601 888 6484
www.gatescarbondrive.com

Information for North and South America

Gates Carbon Drive
ATTN: Marc Seemann
1551 Wewatta St
Denver, CO 80202
USA

Phone: 303-744-4593

Belt Line Specification – Exerpt from Gates Carbon Drive technical documentation

Technical Drawings

A12 Documents

Content of the above ZIP file "Thru axle parts - Rohloff A12 (3d-STEP, PDF, DXF)"