Sprocket tool
Threaded sprocket and sprocket Carrier remover tool
The Rohloff Sprocket Remover Tool should be used together with a chain-whip and 24mm wrench, to remove original threaded sprockets from a SPEEDHUB 500/14 unit. Removal of our new splined sprocket Carrier and original Carbon Drive Carrier can also be accomplished with the use of this tool.
The lock-ring which secures Carbon Drive sprockets to the Lock-ring Carrier, can be loosened and secured to the correct torque, using the special lock-ring tool (Art.#8518)
Set of cutting aids
Easily trim shifter cables to the correct length
It is near impossible to cut SPEEDHUB shifter cables more precisely. The brass measurement tubes are simply slipped over the shifter cables, pushed up to the housing and the protruding inner cable then trimmed at the end. Set consists of 2 tubes; one at 165mm for the internal hub cable, and one at 200mm for the external shifter cable.
Cable hook
Shifter cable trimming tool for the Internal Gear Mech.
The length of the shifter cables protruding after the cable adjusters of an Internal Gear Mech, can vary wildly depending upon the frames rear triangle length. The Cable Hook tool enables shifter cables for Internal Gear Mechs to be trimmed precisely, regardless of frame design.
Service Box Content
| Description: | Article. No.: | |
| 8190 | Rubber grip for twist shifter "light" | 1 |
| 8191 | Twist shifter cable stoppers 1+14 for twist shifter "light" | 2 |
| 8193 | TX20 screws and clamp for twist shifter "light" | 1 |
| 8194 | Cable pulley for twist shifter "light" | 1 |
| 8205 | Drain screw | 1 |
| 8231 | Torque Arm screws with washers | 1 |
| 8236 | Axle-plate Torx screws (6 pcs.) | 2 |
| 8243 | Chainring spacers (5 units) | 1 |
| 8248 | Conversion kit Chain Tensioner | 1 |
| 8251 | Chain Tensioner jockey wheels | 1 |
| 8257 | Long mounting bolt + Distancing washers for chain tensioner | 1 |
| 8260 | Cable Guide 0° (straight type) with frame clamp | 1 |
| 8262 | Pipe Clamps for Art.No. 8240 | 1 |
| 8263 | TS Axle nuts (M10 x 1) including washers | 1 |
| 8268 | Shifter cable set: 2x inner (1.1mm) + housing 1.8m | 1 |
| 8271 | Hub cables for Internal incl. tubes and ties | 1 |
| 8274 | Bayonet connectors, 1x male type, 1x female type | 1 |
| 8275 | Freewheel springs (2 units) | 1 |
| 8295 | Owners Manual Rohloff SPEEDHUB 500/14 | 1 |
| 8410 | Oil change kit (with syringe, drain screw and filler hose) | 1 |
| 8504 | TX20 Torx T-Grip key | 1 |
| 8506 | Cable hook for shifter cables (internal gear mech) | 1 |
| 8508 | Sprocket tool 135/142/170/177 | 1 |
| 8517 | Silencing Grease | 2 |
| 8540 | Splined Carrier | 1 |
| 8540 | Splined Carrier with snap ring | 1 |
| 8540s | Splined Carrier "slim" with snap ring | 1 |
| 8544 | Splined Sprocket 16T | 1 |
| 8570 | Grub screw bayonet connectors | 1 |
| 8573 | Hub cable Easy Set (from Serial no. 25300) | 1 |
| 8701 | Empty Box | 1 |
| 8704 | Cable adjusters for cable box | 1 |
| 8706 | Washer and circlip for Chain Tensioner | 1 |
| 8707 | Bolt and circlip for locating fork (long torque arm) | 1 |
| 8709 | Bayonet springs | 1 |
| 8710 | Paper gasket kit for axle-ring | 1 |
| 8713 | Set of hub/shifter cable measuring aids 165 + 200mm | 1 |
E-14 Diagnosic Kit Content
| Description: | Article. No.: | Amount: |
| 8801 | Rohloff E-14 Switch Unit | 1 |
| 8802 | Rohloff E-14 DC/DC CAN Converter | 1 |
| 8803 | Rohloff E-14 Shifter Unit (for diagnostic and cross exchange only, not for re-sale) | 1 |
| 8810 | 1000mm Extension Cable (lilac, 6-pole, Rohloff E-14 Shifter Unit ⟷ Rohloff E-14 DC/DC CAN Converter) | 1 |
| 8811 | 1000mm Extension Cable (blue, 4-pole, Rohloff E-14 DC/DC CAN Converter ⟷ Rohloff E-14 Switch Unit) | 1 |
| 8714 | Axleplate Screws and Paper Gasket Set | 1 |
| Original Rohloff E-14 Owners Manual | 1 |
