Speedhub Tools

Professional tools for your SPEEDHUB

Replace your old SPEEDHUB threaded sprocket with the Sprocket Remover Tool or trim your cables to length with our Cable Hook and Cutting Aids.

Sprocket tool

Threaded sprocket and sprocket Carrier remover tool

The Rohloff Sprocket Remover Tool should be used together with a chain-whip and 24mm wrench to remove the original threaded sprockets from a SPEEDHUB. Removal of our new splined sprocket Carrier and original Carbon Drive Carrier can also be accomplished with the use of this tool.

Manual Note

The method illustrating how to reverse and/or replace the SPEEDHUB sprocket is shown in the Owners Manual - Service and Repairs section.

To the operating instructions

Variants

Description: Article No.
Sprocket tool for CC/TS 135mm/170mm and 142mm/177mm with A12 Adapter/Screw 8508
Sprocket tool XXL for CC 190mm/A12-197 with A12 Adapter/Screw 8509

Set of cutting aids

Easily trim shifter cables to the correct length

It is near impossible to cut SPEEDHUB shifter cables more precisely. The brass measurement tubes are simply slipped over the shifter cables, pushed up to the housing and the protruding inner cable then trimmed at the end. Set consists of 2 tubes; one at 165mm for the internal hub cable, and one at 200mm for the external shifter cable.

Manual Note

A full description of these articles and their correct use can be found in the Rohloff SPEEDHUB 500/14 Owners Manual.

To the operating instructions

Cable hook

Shifter cable trimming tool for the Internal Gear Mech.

The length of the shifter cables protruding after the cable adjusters of an Internal Gear Mech, can vary wildly depending upon the frames rear triangle length. The Cable Hook tool enables shifter cables for Internal Gear Mechs to be trimmed precisely, regardless of frame design.

Manual Note

A full description of these articles and their correct use can be found in the Rohloff SPEEDHUB 500/14 Owners Manual.

To the operating instructions

Service Box

Order for replacement SPEEDHUB components

A tidy workshop is an efficient workshop. The Rohloff Service Box includes all spare parts for the SPEEDHUB that are prone to wear-and-tear, ensuring a fast SPEEDHUB service is always within reach.

Service Box Content

Description: Article. No.:  
8190 Rubber grip for twist shifter "light" 1
8191 Twist shifter cable stoppers 1+14 for twist shifter "light" 2
8193 TX20 screws and clamp for twist shifter "light" 1
8194 Cable pulley for twist shifter "light" 1
8205 Drain screw 1
8231 Torque Arm screws with washers 1
8236 Axle-plate Torx screws (6 pcs.) 2
8243 Chainring spacers (5 units) 1
8248 Conversion kit Chain Tensioner 1
8251 Chain Tensioner jockey wheels 1
8257 Long mounting bolt + Distancing washers for chain tensioner 1
8260 Cable Guide 0° (straight type) with frame clamp 1
8262 Pipe Clamps for Art.No. 8240 1
8263 TS Axle nuts (M10 x 1) including washers 1
8268 Shifter cable set: 2x inner (1.1mm) + housing 1.8m 1
8271 Hub cables for Internal incl. tubes and ties 1
8274 Bayonet connectors, 1x male type, 1x female type 1
8275 Freewheel springs (2 units) 1
8295 Owners Manual Rohloff SPEEDHUB 500/14 1
8410 Oil change kit (with syringe, drain screw and filler hose) 1
8504 TX20 Torx T-Grip key 1
8506 Cable hook for shifter cables (internal gear mech) 1
8508 Sprocket tool 135/142/170/177 1
8517 Silencing Grease 2
8540 Splined Carrier 1
8540 Splined Carrier with snap ring 1
8540s Splined Carrier "slim" with snap ring 1
8544 Splined Sprocket 16T 1
8570 Grub screw bayonet connectors 1
8573 Hub cable Easy Set (from Serial no. 25300) 1
8701 Empty Box 1
8704 Cable adjusters for cable box 1
8706 Washer and circlip for Chain Tensioner 1
8707 Bolt and circlip for locating fork (long torque arm) 1
8709 Bayonet springs 1
8710 Paper gasket kit for axle-ring 1
8713 Set of hub/shifter cable measuring aids 165 + 200mm 1